Cat40 Tooling Package Fit Haas Er32 Er16 Collet End MILL Drill Chuck Face MILL

  

CAT40 STARTING TOOLING PACKAGE FIT ON HAAS. ER32 ER16 COLLET SET, COLLET CHUCK, END MILL HOLDER, DRILL CHUCK, FACE MILL BRAND NEW. High Speed True Balance in 15-20K RPM.

6PC END MILL HOLDER 3PC ER32 COLLET CHUCK 2PC ER16 COLLET CHUCK 1PC 1/2 Keyless Drill Chuck 1PC Face Mill Cutter 12PC ER32 COLLET SET BY 1/ 16 10PC ER16 COLLETS SET BY 1/ 32 FREE HAAS PULL STUD ON EACH TOOL HOLDER AND CHUCK FREE SPANNER WRENCH ON COLLET CHUCK AND DRILL CHUCK. With Free HAAS pull stud, can be used on HAAS CAT40 spindle cnc v mill. Be aware on many bad and rough tooling that you see on site as well.

I have many customers asked me the same questions that how about yours vs theirs. I post run out numbers and video in description, and you can test after receive. However, many other vendors are over or false. Their tool holders and collets. Based on customers who got ripped off from many cheap sellers, the total run out on their bad tool holders and collets could be in 5 thousands rather than 5 tenth, and the drill chuck could be in 10 thousands, plus pull studs break left right.

This is my chuck and collets, see two videos below, indicator is the same 0.0001. Total run out of holder and good set of collets are less than 0.0005", tool holder alone without collets are 0.0001". Since it's balanced, so regardless of speed, holder and collets will running true. Both tool holders and collets must be running true in order get total run out to minimum. Video will open in a new window. 6PC CAT40 End Mill Holder. 6PC Common Size: 1/4, 3/8, 1/2, 5/8, 3/4, 1. Precision high speed end mill holder for durability and rigidity.

Provides a very close tolerance fit with minimum runout between the tool holder's bore and the cutting tool. Thru Hole of the tool holder allows the use of Thru Coolant Tools when used with a Thru Coolant retention knob. Both ER32 and ER16 Chuck Gage or projection length of ER 16 is 2.75. Fully ground flange and V-groove - easy on tool changers for less spindle and.

V-Flange CAT 40 is production balanced to high speed spindle turning and meet standard industrial needs. Hardened and ground to ensure maximum accuracy.

Through spindle coolant capability from pull stud to collets. 1PC Precision Keyless Drill Chuck. Keyless Drill Chuck 1/2 Capacity. Drill chuck has very strong holding power.

V-Flange CAT 40 is production balanced and meet standard industrial needs. 5PC general purpose carbide inserts. Combination of a tough, special cemented carbide substrate and CVD coated grade for milling of steel up to 30-35 HRC before heat treat. 12PC ER 32 Collets Set By 1/16.

Ma de of high grade spring steel. Ground roughness is Ra0.4 Microns, plus overall fine polish.

1/4"; 5/16"; 3/8"; 7/16"; 1/2"; 9/16"; 5/8"; 11/16"; 3/4. 0.0003 or 5u m. In order to make all collets run ning true, on your side, make sure your machine spindle and chuck holder running true, on my side, I'll make sure all those collets running in tenth. Special angled slots increase rigidity. Better overall balance of tool holder assembly.

Protects tool holder from contaminants. Use with any standard ER collet chucks for coolant-thru tool applications. 10PC ER16 Collets by 1/32.

1/32", 1/16", 3/32", 1/8", 3/16" , 7/32", 1/4", 5/16". Free Items Include d in this pacakge. Free CAT 40 pull stud. All items include: 6PC common size end mill holder, 3PC ER32 chuck, 2PC ER16 c huck, 1PC drill chuck, 1PC face mill cutter, 12 PC ER32 collets, 10PC E R 16 collets and more.

Total runout is a sum of runout of collets, chuck or holder, and machine spindle. On CAT40 or BT40 spindle, you're expecting half thousands overall runout with these collets and collet holder. So collets alone is about 3 tenth, then you add chuck run out 1 or 2 tenth, it comes up about half thousands or 5 tenth, so choose correct tooling for correct application.